Browse by Tags

Re: Coil Relocation - where to run the loom?

fierysport ... Here's your fix [ ] The Pink/White wire belongs on the rear Intake APS Cyl 1 as i stated in the Yankee forum. Be sure you have the vacuum line connected as shown. Happy to see you solved your self inflicted problem [ ] LOL ozwarrior ... thanks for the compliment [:I] It never...

Posted to Australia (Forum) by AlanH on 08-06-2007
Filed under: VBAK, Electrical
Re: Urgent Help Needed - Coil Relocation Problems

1. That's the Engine light that's on. There is no oil light on the Warrior 2. Unless you were on reserve when you pulled your tank there isn't a problem. I've ridden around without my gas tank and not have the lamp come on. 3. Sounds like you might have swapped a connector or wires. The...

Posted to Technical Discussion (Forum) by AlanH on 08-05-2007
Filed under: Electrical, VBAK
Re: bike will not idle and pops through throttle body

This sounds familar. See if these threads help you out: http://rswarrior.com/forums/p/25983/378121.aspx#378121 http://rswarrior.com/forums/p/57975/820755.aspx#820755 Edited: The black plug for the atmospheric pressure sensor that doesn't have a vacuum hose has a solid pink wire! The No. 1 cyl (Rear...

Posted to Technical Discussion (Forum) by AlanH on 08-09-2007
Filed under: Electrical, VBAK
Re: Problem with coil relocation plate & V-BAK

[quote user="baclay9"] I guess I just need to do some more moving around until I get it right. I got so frustrated with it yesterday I had to walk away from it. I did start the bike for a minute though so I guess I got everything hooked up correctly. Let me ask you this. I wound the excess...

Posted to Technical Discussion (Forum) by AlanH on 08-19-2008
Filed under: VBAK, How to, Coil Relocating Plate
Re: Coil relocate question

With Churchkey's VBAK i found it necessary to unwrap approx 6"-8" of the harness for rerouting of the coil primary, LCV cable and sensor wires. This was the most difficult part of the mod IMO and takes some vision, so take your time and do it correctly when you rewrap the wires so that...

Posted to Technical Discussion (Forum) by AlanH on 07-29-2007
Filed under: VBAK, How to, Coil Relocating Plate
Re: Problem with coil relocation plate & V-BAK

[quote user="baclay9"] I put the Akitadog plate and the V-BAK on and am having a small problem. Everything went together good but my tank isn't fitting right. I can tell one of the coils is touching the front facing velocity stack. I have adjusted the stack every which way I can but it...

Posted to Technical Discussion (Forum) by AlanH on 08-19-2008
Filed under: VBAK, How to, Coil Relocating Plate
Re: Plastic liner in tank?

You can also run a hose from your car tailpipe into the filler neck on the tank,and let the car run for about 10 or 15 minutes. I use to make aluminum gas tanks,and if I had to weld on a used tank, this was the method we used. It really works.

Posted to Technical Discussion (Forum) by Gilly on 03-19-2009
Filed under: VBAK
Re: Fuel tank vent hoses

Mine is run similar to Churchkey's except that i retained the roll over valve

Posted to Technical Discussion (Forum) by AlanH on 02-10-2008
Filed under: Fuel Tank, VBAK
Rightside cleanup, airbox removed, new mount & cover installed. VBAK installed & AIS removed

Rightside cleanup for under $25.00.

Posted to ravener (Gallery) by ravener on 08-19-2009
Filed under: cover, clean up., Rightside, right side, cleanup, VBAK, AIS removed
DIY VBAK - photo 2

DIY Vbak. ABS 45° street elbow w/UNI Pod filters, 3/8 breathers

Posted to c2000 (Gallery) by c2000 on 07-31-2009
Filed under: bikes, 102, warrior, Yamaha, yamaha warrior, Vbak, BAK, DIY VBak, Rs Warrior

Page 1 of 2 (12 items) 1 2 Next >