The Yamaha Road Star Warrior Forum

Just arrived.  I got the 1.5 inch diameter 9 inch rise.  Amazing looking chrome, Amazing quality, flawless joints where the risers meet the cross bar.

Pics later.

Will be installed over the dark depression season (winter).  I'll be taking a lot of step by step pictures and notes along the way, riser bolt size, electrical wire extension lengths, soldered/mecahanical splices, etc, etc,.  Wires will be routed internally.

 I can't wait to see the write up of this, I have to do the same thing but with the CP-1120's

i'm looking forward to it since it's the bar i've been looking at.

Cheers!  

 Funny, I actually find myself "hoping" that when I dissassemble my front end this winter to check for something bent, that I actually find something....safety first right!!!! santa can't refuse safety!!!!! will be watching for the pics jeff!

I think you should start now!

OldMan:

I think you should start now!

What if I told you I haven't "completely" finished the deck yet

needanewscooter:

OldMan:

I think you should start now!

What if I told you I haven't "completely" finished the deck yet

Honduranheat:

i'm looking forward to it since it's the bar i've been looking at.

 

Cheers!  

Then please check your riser spacing, You need 3-1/2" riser spacing for these to be a direct bolt-on.  I'm planning to do a little bit of machining to the top clamp of the triple-tree if need be.

needanewscooter:

Honduranheat:

i'm looking forward to it since it's the bar i've been looking at.

 

Cheers!  

Then please check your riser spacing, You need 3-1/2" riser spacing for these to be a direct bolt-on.  I'm planning to do a little bit of machining to the top clamp of the triple-tree if need be.

needanewscooter:

Then please check your riser spacing, You need 3-1/2" riser spacing for these to be a direct bolt-on.  I'm planning to do a little bit of machining to the top clamp of the triple-tree if need be.

100mm riser centers to be exact on the Warrior (Approx 4") ... 3-1/2" spacing is std HD

As Darkstar stated, it's a bolt-on

AlanH:

needanewscooter:

Then please check your riser spacing, You need 3-1/2" riser spacing for these to be a direct bolt-on.  I'm planning to do a little bit of machining to the top clamp of the triple-tree if need be.

You got your wires crossed there buddy

100mm riser centers to be exact on the Warrior (Approx 4") ... 3-1/2" spacing is std HD

As Darkstar stated, it's a bolt-on

Nope, my wires ain't crossed, the Carlini's I just got have 3-1/2" riser spacing, I know the warrior is 100mm (3.937").  Carlini didn't give an option for nor did it specify the riser spacing, I knew a few on here put them on a warrior so I ordered myself a set.  I learned it's 3-1/2" spacing when I opened up the box.  I have a message into Carlini to see if both are available, if yes then I send these back for an excahnge.  If not I got myself a small challenge to get these on.

Maybe, just maybe you will find your front forks bend and can (for safety) go to ebay and end up with an R-1 front end complete with 6 piston brakes!   Obviously a safer setup!!

you just made my brain hurt

needanewscooter:

Nope, my wires ain't crossed, the Carlini's I just got have 3-1/2" riser spacing, I know the warrior is 100mm (3.937").  Carlini didn't give an option for nor did it specify the riser spacing, I knew a few on here put them on a warrior so I ordered myself a set.  I learned it's 3-1/2" spacing when I opened up the box.  I have a message into Carlini to see if both are available, if yes then I send these back for an excahnge.  If not I got myself a small challenge to get these on.

Sorry to hear this but IMO someone is taking you down the garden path. Very recently i had an interest in the Carlini bars and when i last checked their distributors were PCS & Phat Perf for the metric bars as shown in the enclosed links

• http://www.phatperformanceparts.com/ProductDetails.asp?ProductCode=MSS150%2D9
• http://www.pacificcoaststar.com/pcs/yamaha_t_bars.htm

Good Luck

Hey, no problem Alan, I welcome the help.  Thanks for those links.  The pacific coast star site details the riser width at 4 inches which certainly puts my mind at ease "big time".  Carlini hasn't replied back to me yet but I'm sure I can do an exchange.  I'll up-date the topic as soon as I get this straightened out on my end.  Thanks again!